Table of Contents
- Introduction
- Modifications to Manual
- Part A: Organization and Administration
- Part B: Minimum Testing and Certification Requirements
- Part C: Materials Sampling/Testing/Inspection Requirements
- Section D: DOH Test Methods
- DOH 2 - Method of Determination of Moisture Content
- DOH 3 - Sampling Soil and Aggregate Base
- DOH 4 - Borrow Pit Sampling for Source Approval
- DOH 5 - Sampling Stone, Slag, Gravel, Sand, and Stone Block for Use as Highway Material
- DOH 6 - Approval of Sources of Fine and Coarse Aggregate
- DOH 7 - Source Control - Borrow
- DOH 8 - Sampling of Portland Cement
- DOH 9 - pH of Soil and Topsoil
- DOH 10 - Sampling Fresh Portland Cement Concrete
- DOH 11 - Making and Curing Concrete Compression and Flexural Test Specimens in the Field
- DOH 12 - Obtaining and Testing Drilled Portland Cement Concrete Cores
- DOH 13 - Guidelines for Acceptance of Bituminous Concrete from Hot Mix Storage Bins
- DOH 15 - Testing of Reinforcing Steel
- DOH 16 - Determining the Maximum Density of Bituminous Concrete Utilizing the Control Strip Procedure
- DOH 17 - Checking Plant Scales
- DOH 19 - Recommended Practice for Description of Soils (Visual - Manual Procedure)
- VTM 51 - Filtering Efficiency and Flow Rate of a Filter Fabric
- Section E: Standard Forms
- Section F: Glossary
- Section G: Materials Administration Unit Manual
- Section H: Relevant Charts and Tables
List of Figures
List of Tables
- B-1: Minimum Testing Frequencies and Test Procedures
- C-1: Division 200 - Sampling Methods
- C-2: Division 200 - Sample Identification Numbering
- C-3: Division 200 - Test Methods
- C-4: Division 200 - Certification Test Procedures / Material Standards
- C-5: Division 300 - Distribution of Test Results
- C-6: Division 300 - Sampling Methods
- C-7: Division 300 - Sample Identification Numbering
- C-8: Division 300 - Test Methods
- C-9: Division 300 - Certification Test Procedures / Material Standards
- C-10: Division 400 - Sampling Methods
- C-11: Division 400 - Sample Identification Numbering
- C-12: Division 400 - Test Methods
- C-13: Division 400 - Certification Test Procedures / Material Standards
- C-14: Division 500 – Sampling Quantities at Portland Cement Concrete Plants
- C-15: Division 500 – Test Properties and Testing Frequency of Portland Cement Concrete in the Field
- C-16: Division 500 – Distribution of Test Results and Reports
- C-17: Division 500 - Sampling Methods
- C-18: Division 500 - Sample Identification Numbering
- C-19: Division 500 - Test Methods
- C-20: Division 500 - Certification Test Procedures / Material Standards
- C-21: Division 600 –Sampling Rates of Cast-In-Place Concrete Pipe
- C-22: Division 600 – Load Bearing Test Schedule
- C-23: Division 600 - Sampling Methods
- C-24: Division 600 - Sample Identification Numbering
- C-25: Division 600 - Test Methods
- C-26: Division 600 - Certification Test Procedures / Material Standards
- C-27: Division 700 - Sampling Methods
- C-28: Division 700 - Sample Identification Numbering
- C-29: Division 700 - Test Methods
- C-30: Division 700 - Certification Test Procedures / Material Standards
- H-1: Approximate Conversions from English to SI Units
- H-2: Approximate Conversions from SI to English Units
- H-3: SI Prefixes
- H-4: Total Moisture Determinations Conversion Table (Sand)
- H-5: Total Moisture Determinations Conversion Table (Coarse Aggregate)